- 1.1180, DIN CM35 round bar
- 1.1180, DIN CM35 forging
- 1.1180, DIN CM35 sheet
- 1.1180, DIN CM35 flat bar
- 1.1180, DIN CM35 pipe
1.1180, DIN CM35
We can produce 1.1180, DIN CM35 stainless steel round rods, 1.1180, DIN CM35 forging,sheet,coil,and profiledstrip,Deformed steel,flat steel,mould,steel wire,have all specifications. With DuoNian production experience, strict control 1.1180, DIN CM35 chemical composition and 1.1180, DIN CM35 mechanical properties.From casting, forging, steel to hot and cold rolling process, heat treatment, etc, we have the control of professional engineers. We have advanced precision machining equipment, according to the requirements of users machining. in order to achieve the most satisfied with the user requirements.
Production specification
Round bar steel: 1mm to 3500mm
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.
1.1180, DIN CM35
Designation by Standards
| Brand Name | LH No. | Mat. No. | DIN | EN | AISI |
| CM35 | 635 | 1.1180 | CM35 | - | - |
Chemical Composition (in weight %)
| C | Si | Mn | Cr | Mo | Ni | V | W | Others |
| 0.35 | max. 0.40 | 0.65 | max. 0.40 | max. 0.10 | max.0.40 | - | - | (Cr+Mo+Ni) = max. 0.63 |
Description
Non alloy special sructural steels: Structural steels with average C < 0,50%.
Applications
Steels for quenching and tempering, automobile and motor construction parts.
Physical properties (avarage values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.86
Soft Annealing
Heat to 650-700oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 183.
Normalizing
Normalizing temperature: 860-900oC.
Hardening
Harden from a temperature of 840-880oC, 840-880oC followed by water or oil quenching.
Tempering
Tempering from the quenched condition may be done at 550-660oC depending upon the strength desired.
Forging
Hot forming temperature: 1100-850oC.
Machinability
Machinability is good, rated at 60% that of the AISI 1112 alloy used as a 100% machining rated steel.
Corrosion Resistance
This is a steel alloy and will rust if not protected. it is not corrosion resistant.
Welding
CM35 steel is weldable by all of the welding methods. However with its higher carbon content it is important to use both pre-heat at 150 to 260oC and post-heat at 590 to 650oC practice per an approved welding procedure.
Cold working
In the annealed state the CM35 alloy is readily cold worked by conventional methods.
Mechanical properties
1.1180, DIN CM35 Mechanical properties,Our production completely according to the 1.1180, DIN CM35 standards to meet the 1.1180, DIN CM35 mechanical performance, can also according to the customer request, to meet the requirements of customers of 1.1180, DIN CM35 mechanical properties.
Heat treatment
1.1180, DIN CM35 Heat treatment,Our production completely according to the 1.1180, DIN CM35 standards to meet the 1.1180, DIN CM35 Heat treatment, can also according to the customer request, to meet the requirements of customers of 1.1180, DIN CM35 Heat treatment.
Machining
1.1180, DIN CM35 Machining,Our production completely according to the 1.1180, DIN CM35 standards to meet the 1.1180, DIN CM35 Machining, can also according to the customer request, to meet the requirements of customers of 1.1180, DIN CM35 Machining.
Welding performance
1.1180, DIN CM35 Welding performance,Our production completely according to the 1.1180, DIN CM35 standards to meet the 1.1180, DIN CM35 Welding performance, can also according to the customer request, to meet the requirements of customers of 1.1180, DIN CM35 Welding performance.
Related hot word search:1.1180 DIN CM35 round bar 1.1180, DIN CM35,forging 1.1180, DIN CM35,1.1180, DIN CM35 sheet,coil 1.1180, DIN CM35,1.1180, DIN CM35 flat bar,pipe 1.1180, DIN CM35,1.1180, DIN CM35 Lrregular
Prev:1.1140, DIN Cm15, AISI 1015
Next:1.1201, DIN Cm45, AISI 1045