Home > Tool Steel > 1.2083 Tool Steel

1.2083 Tool Steel

We can produce 1.2083 Tool Steel stainless steel round rods, 1.2083 Tool Steel forging,sheet,coil,and profiledstrip,Deformed steel,flat steel,mould,steel wire,have all specifications. With DuoNian production experience, strict control 1.2083 Tool Steel chemical composition and 1.2083 Tool Steel mechanical properties.From casting, forging, steel to hot and cold rolling process, heat treatment, etc, we have the control of professional engineers. We have advanced precision machining equipment, according to the requirements of users machining. in order to achieve the most satisfied with the user requirements.

Production specification

Round bar steel: 1mm to 3500mm
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.

1.2083 Tool Steel

1.2083 is a chromium alloyed stainless plastic Mould-steel/" target="_blank" class="keylink">mould steel, which is characterised by good polishability, good hardenability giving high hardness, with fair corrosion resistance.

TYPICAL ANALYSIS
C.	Si.	Mn.	Cr.
0.38%	0.75%	0.50%	13.50%

Forging:

Heat slowly and uniformly to 1000°C. After forging cool slowly.

Annealing:

Heat slowly to 780°C. Slowly cool in furnace.

Hardening:
Pre heat to 600-700°C until heated through. (Austenitizing temperature 1025°C.) Continue heating to the final hardening temperature of 980-1050°C and allow the component to be heated through. Protect against decarburisation by using neutral salt bath, controlled atmosphere furnace or vacuum. Air cool or quench in oil.

Tempering:
Heat uniformly and thoroughly at the selected tempering temperatures and hold at heat for one hour per inch of total thickness. Double tempering is recommended.

Tempering °C	100	200	300	400	500	600
HRc	56	54	52	54	53	34

Nitriding:

Nitriding of 1.2083 gives it a hard surface which is very resistant to wear and corrosion. Howe ver , the nitrided surface reduces the corrosion resistance. Surface hardness after nitriding at 525°C in ammonia gas will be approximately 1000HV.

Temperature	Time	Approximate Depth of Case
525°C	20 hours	0.20mm
525°C	30 hours	0.30mm
525°C	60 hours	0.40mm

Welding:
Due to the high risk of crack formation welding of 1.2083 stainless steel should be avoided, if possible. When, howe verwelding is essential, the following serves as a guide:

A.  Welding of soft annealed 1.2083 stainless steel.
·       Preheat to 300 - 500°C
·       Weld at 300-500°C
·       Immediately stress relieve

B.  Repair welding of 1.2083 stainless steel in hardened and tempered condition.
·       Preheat to the tempering temperature (min. 200°C) previously used.
·       Start welding  at tempering temperature
·       Re heat immediately to tempering temperature, but max. 300°C. Soaking time 3 hours.
·       Cool in air to approximately 80°C.
·       Re heat immediately to tempering temperature, but max. 300°C. Soaking time 3 hours.
Electrode: Hard facing electrode.

Physical Properties:	Temperature
(50 HRc)	20°C	200°C	400°C
Density
kg/m³	7.8	7.75	7.70
Coefficient of thermal expansion
per °C	-	11.0 x 10-6	11.4 x 10-6
from 20°
Thermal conductivity
cal/cm.s °C	54.9 x 10-3	57.3 x 10-3	59.7 x 10-3
Modulus of elasticity
Kp/mm²	21 900	21 400	19 400
N/mm²	215 000	210 000	190 000
Specific Heat
cal/g °C	0.110
Tensile Strength
kp/mm²	180	168	158
N/mm²	1 780	1 650	1 550
Yield Point
kp/mm²	150	139	129
N/mm²	1 460	1 360	1 250
Reduction of Area
%	30	40	40
Elongation
%	10	12	12

Mechanical properties

1.2083 Tool Steel Mechanical properties,Our production completely according to the 1.2083 Tool Steel standards to meet the 1.2083 Tool Steel mechanical performance, can also according to the customer request, to meet the requirements of customers of 1.2083 Tool Steel mechanical properties.

Heat treatment

1.2083 Tool Steel Heat treatment,Our production completely according to the 1.2083 Tool Steel standards to meet the 1.2083 Tool Steel Heat treatment, can also according to the customer request, to meet the requirements of customers of 1.2083 Tool Steel Heat treatment.

Machining

1.2083 Tool Steel Machining,Our production completely according to the 1.2083 Tool Steel standards to meet the 1.2083 Tool Steel Machining, can also according to the customer request, to meet the requirements of customers of 1.2083 Tool Steel Machining.

Welding performance

1.2083 Tool Steel Welding performance,Our production completely according to the 1.2083 Tool Steel standards to meet the 1.2083 Tool Steel Welding performance, can also according to the customer request, to meet the requirements of customers of 1.2083 Tool Steel Welding performance.

Prev:M42 Tool Steel
Next:1.2842 Tool Steel