- 1.2419, DIN 105WCr6 round bar
- 1.2419, DIN 105WCr6 forging
- 1.2419, DIN 105WCr6 sheet
- 1.2419, DIN 105WCr6 flat bar
- 1.2419, DIN 105WCr6 pipe
1.2419, DIN 105WCr6
We can produce 1.2419, DIN 105WCr6 stainless steel round rods, 1.2419, DIN 105WCr6 forging,sheet,coil,and profiledstrip,Deformed steel,flat steel,mould,steel wire,have all specifications. With DuoNian production experience, strict control 1.2419, DIN 105WCr6 chemical composition and 1.2419, DIN 105WCr6 mechanical properties.From casting, forging, steel to hot and cold rolling process, heat treatment, etc, we have the control of professional engineers. We have advanced precision machining equipment, according to the requirements of users machining. in order to achieve the most satisfied with the user requirements.
Production specification
Round bar steel: 1mm to 3500mm
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.
1.2419, DIN 105WCr6
Designation by Standards
| Brand Name | LH No. | Mat. No. | DIN | EN | AISI |
| MERILOEX | 823 | 1.2419 | 105WCr6 | 107WCrR5 | - |
Chemical Composition (in weight %)
| C | Si | Mn | Cr | Mo | Ni | V | W | Others |
| 1.05 | 0.25 | 0.96 | 1.00 | - | - | - | 1.15 | - |
Description
Medium alloy cold work steel, oil hardening type. Good dimesional and cutting stability; slightly lower hardenability and wear resistance, compared with highly chromium alloyed steels, but better toughness.
Applications
Cutting and punching tools for sheet thickness up to 6 mm, also for paper and plastics, roll shear blades for sheet thickness up to 6 mm, small bending and drawing tools, thread cutting tools, reamers, woodworking tools, gauges and other measuring tools, small inserts and plastic moulds.
Physical properties (avarage values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.85
Thermal conductivity [W/m.K]: 30.0
Electric resistivity [Ohm mm2/m]: 0.35
Specific heat capacity[J/g.K]: 0.46
Coefficient of Linear Thermal Expansion 10-6 oC-1
| 20-100oC | 20-200oC | 20-300oC | 20-400oC | 20-500oC | 20-600oC | 20-700oC |
| 12.6 | 13.3 | 13.8 | 14.2 | 14.6 | 15.0 | 15.3 |
Continuous Cooling Transformation (CCT) Diagram
Soft Annealing
Heat to 720-750oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 230.
Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to approx. 650oC, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.
Hardening
Harden from a temperature of 800-830oC followed by oil quenching or warm bath quenching approx. 200oC. Hardness after quenching is 63-65 HRC.
Tempering
Tempering temperature: See the data bellow.
Tempering Temperature (oC) vs. Hardness (HRC)
| 100oC | 200oC | 300oC | 400oC | 500oC | 600oC | 650oC |
| 64 | 61 | 58 | 54 | 49 | 41 | 30 |
Tempering Diagram
Forging
Hot forming temperature: 1050-850oC.
Machinability
No data.
Mechanical properties
1.2419, DIN 105WCr6 Mechanical properties,Our production completely according to the 1.2419, DIN 105WCr6 standards to meet the 1.2419, DIN 105WCr6 mechanical performance, can also according to the customer request, to meet the requirements of customers of 1.2419, DIN 105WCr6 mechanical properties.
Heat treatment
1.2419, DIN 105WCr6 Heat treatment,Our production completely according to the 1.2419, DIN 105WCr6 standards to meet the 1.2419, DIN 105WCr6 Heat treatment, can also according to the customer request, to meet the requirements of customers of 1.2419, DIN 105WCr6 Heat treatment.
Machining
1.2419, DIN 105WCr6 Machining,Our production completely according to the 1.2419, DIN 105WCr6 standards to meet the 1.2419, DIN 105WCr6 Machining, can also according to the customer request, to meet the requirements of customers of 1.2419, DIN 105WCr6 Machining.
Welding performance
1.2419, DIN 105WCr6 Welding performance,Our production completely according to the 1.2419, DIN 105WCr6 standards to meet the 1.2419, DIN 105WCr6 Welding performance, can also according to the customer request, to meet the requirements of customers of 1.2419, DIN 105WCr6 Welding performance.
Related hot word search:1.2419 DIN 105WCr6 round bar 1.2419, DIN 105WCr6,forging 1.2419, DIN 105WCr6,1.2419, DIN 105WCr6 sheet,coil 1.2419, DIN 105WCr6,1.2419, DIN 105WCr6 flat bar,pipe 1.2419, DIN 105WCr6,1.2419, DIN 105WCr6 Lrregular