Home > Tool Steel > 1.2210, DIN 115CrV3, AISI L2

1.2210, DIN 115CrV3, AISI L2

We can produce 1.2210, DIN 115CrV3, AISI L2 stainless steel round rods, 1.2210, DIN 115CrV3, AISI L2 forging,sheet,coil,and profiledstrip,Deformed steel,flat steel,mould,steel wire,have all specifications. With DuoNian production experience, strict control 1.2210, DIN 115CrV3, AISI L2 chemical composition and 1.2210, DIN 115CrV3, AISI L2 mechanical properties.From casting, forging, steel to hot and cold rolling process, heat treatment, etc, we have the control of professional engineers. We have advanced precision machining equipment, according to the requirements of users machining. in order to achieve the most satisfied with the user requirements.

Production specification

Round bar steel: 1mm to 3500mm
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.

1.2210, DIN 115CrV3, AISI L2

Designation by Standards

Brand Name	LH No.	Mat. No.	DIN	EN	AISI
OCR1	804	1.2210	115CrV3	-	L2

Chemical Composition (in weight %)

C	Si	Mn	Cr	Mo	Ni	V	W	Others
1.17	0.23	0.30	0.65	-	-	0.10	-	-

Description
Low alloyed cold working steel/" target="_blank" class="keylink">tool steel.

Applications
Spiral and tap drills, broaching tools, engraving tools, ejectors, metal saws.

Physical properties (avarage values) at ambient temperature
Modulus of elasticity [10³ x N/mm²]: 210
Density [g/cm³]: 7.80
Thermal conductivity [W/m.K]: 33.5, 32 (500^oC), 31 (700^oC)
Electric resistivity [Ohm mm²/m]: 0.33
Specific heat capacity[J/g.K]: 0.46

Coefficient of Linear Thermal Expansion 10^-6 ^oC^-1

20-100^oC	20-200^oC	20-300^oC	20-400^oC	20-500^oC
11.8	12.5	12.9	13.5	13.7

Soft Annealing
Heat to 710-850^oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 223.

Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to approx. 650^oC, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.

Hardening
Harden from a temperature of 780-820^oC, 800-840^oC followed by water or oil quenching. Hardness after quenching is 64-66, 64-66 HRC.

Tempering
Tempering temperature: 100-400^oC.

Tempering Temperature (^oC) vs. Hardness (HRC)

100^oC	200^oC	300^oC	400^oC	450^oC
64	63	59	54	47

Tempering Diagram

Forging
Hot forming temperature: 1050-850^oC.

Machinability
No data.

Corrosion Resistance
This is an steel/" target="_blank" class="keylink">alloy steel and it is not corrosion resistant. It will rust unless protected.

Mechanical properties

1.2210, DIN 115CrV3, AISI L2 Mechanical properties,Our production completely according to the 1.2210, DIN 115CrV3, AISI L2 standards to meet the 1.2210, DIN 115CrV3, AISI L2 mechanical performance, can also according to the customer request, to meet the requirements of customers of 1.2210, DIN 115CrV3, AISI L2 mechanical properties.

Heat treatment

1.2210, DIN 115CrV3, AISI L2 Heat treatment,Our production completely according to the 1.2210, DIN 115CrV3, AISI L2 standards to meet the 1.2210, DIN 115CrV3, AISI L2 Heat treatment, can also according to the customer request, to meet the requirements of customers of 1.2210, DIN 115CrV3, AISI L2 Heat treatment.

Machining

1.2210, DIN 115CrV3, AISI L2 Machining,Our production completely according to the 1.2210, DIN 115CrV3, AISI L2 standards to meet the 1.2210, DIN 115CrV3, AISI L2 Machining, can also according to the customer request, to meet the requirements of customers of 1.2210, DIN 115CrV3, AISI L2 Machining.

Welding performance

1.2210, DIN 115CrV3, AISI L2 Welding performance,Our production completely according to the 1.2210, DIN 115CrV3, AISI L2 standards to meet the 1.2210, DIN 115CrV3, AISI L2 Welding performance, can also according to the customer request, to meet the requirements of customers of 1.2210, DIN 115CrV3, AISI L2 Welding performance.

Prev:1.1554, DIN C110W, AISI W1
Next:1.3505, DIN 100Cr6, AISI 5210