- 1.2327, DIN 86CrMoV7 round bar
- 1.2327, DIN 86CrMoV7 forging
- 1.2327, DIN 86CrMoV7 sheet
- 1.2327, DIN 86CrMoV7 flat bar
- 1.2327, DIN 86CrMoV7 pipe
1.2327, DIN 86CrMoV7
We can produce 1.2327, DIN 86CrMoV7 stainless steel round rods, 1.2327, DIN 86CrMoV7 forging,sheet,coil,and profiledstrip,Deformed steel,flat steel,mould,steel wire,have all specifications. With DuoNian production experience, strict control 1.2327, DIN 86CrMoV7 chemical composition and 1.2327, DIN 86CrMoV7 mechanical properties.From casting, forging, steel to hot and cold rolling process, heat treatment, etc, we have the control of professional engineers. We have advanced precision machining equipment, according to the requirements of users machining. in order to achieve the most satisfied with the user requirements.
Production specification
Round bar steel: 1mm to 3500mm
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.
1.2327, DIN 86CrMoV7
Designation by Standards
| Brand Name | LH No. | Mat. No. | DIN | EN | AISI |
| OHV4 | 816 | 1.2327 | 86CrMoV7 | - | - |
Chemical Composition (in weight %)
| C | Si | Mn | Cr | Mo | Ni | V | W | Others |
| 0.87 | 0.30 | 0.38 | 1.75 | 0.28 | 0.13 | 0.10 | - | - |
Description
Low alloyed cold working steel/" target="_blank" class="keylink">tool steel.
Applications
Cold rolls, back-up rolls, straightening rolls, non-ferrous 2 and 4 high roll mills.
Physical properties (avarage values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.85
Thermal conductivity [W/m.K]: 35.0
Electric resistivity [Ohm mm2/m]: 0.30
Specific heat capacity[J/g.K]: 0.46
Coefficient of Linear Thermal Expansion 10-6 oC-1
| 20-100oC | 20-200oC | 20-300oC | 20-400oC | 20-500oC |
| 12.5 | 13.2 | 13.6 | 14.0 | 14.3 |
Continuous Cooling Transformation (CCT) Diagram
Time-Temperature Transformation (TTT) Diagram
Click the image to enlarge the diagram.
Soft Annealing
Heat to 720-750oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 230.
Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to approx. 650oC, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.
Hardening
Harden from a temperature of 800-820oC, 830-850oC followed by water or oil quenching. Hardness after quenching is 64-67 HRC.
Tempering
Tempering temperature: 200-600oC.
Tempering Temperature (oC) vs. Hardness (HRC)
| 100oC | 200oC | 300oC | 400oC |
| 65 | 61 | 58 | - |
Forging
Hot forming temperature: 1150-850oC.
Machinability
No data.
Mechanical properties
1.2327, DIN 86CrMoV7 Mechanical properties,Our production completely according to the 1.2327, DIN 86CrMoV7 standards to meet the 1.2327, DIN 86CrMoV7 mechanical performance, can also according to the customer request, to meet the requirements of customers of 1.2327, DIN 86CrMoV7 mechanical properties.
Heat treatment
1.2327, DIN 86CrMoV7 Heat treatment,Our production completely according to the 1.2327, DIN 86CrMoV7 standards to meet the 1.2327, DIN 86CrMoV7 Heat treatment, can also according to the customer request, to meet the requirements of customers of 1.2327, DIN 86CrMoV7 Heat treatment.
Machining
1.2327, DIN 86CrMoV7 Machining,Our production completely according to the 1.2327, DIN 86CrMoV7 standards to meet the 1.2327, DIN 86CrMoV7 Machining, can also according to the customer request, to meet the requirements of customers of 1.2327, DIN 86CrMoV7 Machining.
Welding performance
1.2327, DIN 86CrMoV7 Welding performance,Our production completely according to the 1.2327, DIN 86CrMoV7 standards to meet the 1.2327, DIN 86CrMoV7 Welding performance, can also according to the customer request, to meet the requirements of customers of 1.2327, DIN 86CrMoV7 Welding performance.
Related hot word search:1.2327 DIN 86CrMoV7 round bar 1.2327, DIN 86CrMoV7,forging 1.2327, DIN 86CrMoV7,1.2327, DIN 86CrMoV7 sheet,coil 1.2327, DIN 86CrMoV7,1.2327, DIN 86CrMoV7 flat bar,pipe 1.2327, DIN 86CrMoV7,1.2327, DIN 86CrMoV7 Lrregular
Prev:1.2064, DIN 85CrMo7
Next:1.2375, DIN 83CrMoV9