- 1.1181, DIN Ck35, AISI 1035 round bar
- 1.1181, DIN Ck35, AISI 1035 forging
- 1.1181, DIN Ck35, AISI 1035 sheet
- 1.1181, DIN Ck35, AISI 1035 flat bar
- 1.1181, DIN Ck35, AISI 1035 pipe
1.1181, DIN Ck35, AISI 1035
Production specification
Square-shape steel: 1mm to 4000mm
Plate steel:0.1mm to 4000mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-1800mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.
1.1181, DIN Ck35, AISI 1035
Designation by Standards
Brand Name | LH No. | Mat. No. | DIN | EN | AISI |
CK35 | 618 | 1.1181 | Ck35 | - | 1035 |
Chemical Composition (in weight %)
C | Si | Mn | Cr | Mo | Ni | V | W | Others |
0.35 | max. 0.40 | 0.65 | max. 0.40 | max. 0.10 | max.0.40 | - | - | (Cr+Mo+Ni) = max. 0.63 |
Description
CK35 steel has a higher (0.35%) carbon content for greater strength than the lower carbon alloys. It is hardenable by heat treatment, quench and tempering to develop 150 to 250 ksi tensile strength.
Applications
Component parts for automobile industry, e.g., shafts, forgings, flanges, bushings, crankshafts, connecting rods and parts for the machine building industry.
Physical properties (avarage values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.86
Soft Annealing
Heat to 650-700oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 226.
Normalizing
Normalizing temperature: 880-910oC.
Hardening
Harden from a temperature of 805-845oC followed by oil or water quenching.
Tempering
Tempering from the quenched condition may be done at 550-660oC depending upon the strength desired.
Mechanical Properties in Normalized*, Hardened+Tempered Condition
Diameter (mm) | 0.2 % proof stress (N/mm2) | Tensile strength (N/mm2) | Elongation A5 (%) | Reduction Z (%) | Impact strength (J) |
Up to 16* | 300* | 480-670 | 21* | - | - |
17-100* | 270* | 480-670* | 21* | - | - |
101-160* | 245* | 460-650* | 19* | - | - |
Up to 16 | 430 | 630-780 | 17 | 40 | 40 |
17-40 | 370 | 600-750 | 19 | 45 | 40 |
41-100 | 320 | 550-700 | 20 | 50 | 40 |
Forging
Hot forming temperature: 1100-850oC.
Machinability
Machinability is good, rated at 60% that of the AISI 1112 alloy used as a 100% machining rated steel.
Corrosion Resistance
This is a steel alloy and will rust if not protected. it is not corrosion resistant.
Welding
CK35 steel is weldable by all of the welding methods. However with its higher carbon content it is important to use both pre-heat at 150 to 260oC and post-heat at 590 to 650oC practice per an approved welding procedure.
Cold working
In the annealed state the CK35 alloy is readily cold worked by conventional methods.
Mechanical properties
Heat treatment
Machining
Welding performance
Related hot word search:1.1181 DIN Ck35 AISI 1035 round bar 1.1181, DIN Ck35, AISI 1035,forging 1.1181, DIN Ck35, AISI 1035,1.1181, DIN Ck35, AISI 1035 sheet,coil 1.1181, DIN Ck35, AISI 1035,1.1181, DIN Ck35, AISI 1035 flat bar,pipe 1.1181, DIN Ck35, AISI 1035,1.1181, DIN Ck35, AISI 1035 Lrregular
Prev:1.1178, DIN Ck30, AISI 1030
Next:1.1186, DIN Ck40, AISI 1040